(42) The Model SCD1 is a series of signal conditioners which provide bridge excitation, amplification, span and balance controls and a choice of ±10 Vdc and/or 4-20 ma outputs. Primary input power is available in 120 Vac or a variety of Vdc voltage levels.
The SCD1 can accommodate up to four channels with ±10 Vdc outputs or a maximum of 2 channels with 4-20 ma outputs.
Standard SCD1 models are packaged in a NEMA-12 rated cabinet (NEMA-4X packages are available).
Each input channel is connected via a six (6) pin receptacle (PT02A-10-6S)
All output signals are provided at a terminal strip inside the signal conditioner cabinet . Each output signal has an individual terminal connection and each signal ...
Indication is direct. No multipliers are required, thus avoiding ambiguous readings. Resolution is
from 1 pound to 1000 pounds depending on the load capacity of the transducer. Alternate display
units are available.
Operation is extremely simple. For normal use only two controls are involved. Turn on the power
switch, set no load balance, and begin reading applied loads.
A calibration check function is included to provide a quick test of the transducer and instrument
integrity.
The readout system is fully contained in a cast metal case that is both rugged and durable.
Power is provided by a set of rechargeable batteries. Batteries and a recharger with retractable
120 Vac power cord, are included ...
(4) The PLNX- line of indicators are 1, 2, 3, and 4 channel versions with the same basic circuitry and performance
features as the Model PLN-D2. Additional features include different instrument cases, and switching provisions
for one to four channels which accommodate up to four transducers.
Indication is direct. Resolution is from 1 pound to 1000 pounds, depending on full scale transducer capacity.
Alternate display units are available.
Simple operation. For normal use only three controls are involved: Turn on the power switch, select the channel,
set the no load balance or tare reading to zero, and begin reading applied loads.
A shunt calibration function provides a quick test of transducer and indicator ...
The Model PLND4 is a 4-1/2 digit indicator made for use with any full bridge strain gage type transducer.
Indication is direct.
No multipliers are required. Simple operation. For normal
use only two controls are involved: turn on the power switch,
set the no load balance or tare reading to zero, and begin
reading applied loads.
Alternate display units are available.
A calibration check function is included to provide a
quick test of the transducer and instrument integrity.
The read out system is fully contained in a rugged and
durable aluminum alloy case.
Power is provided by a set of rechargeable batteries.
Batteries and a recharger, operable on 110 Vac or 220 Vac,
are included within ...
(3) The 3550’s advanced electronics and simple
interface make it easy to set up and operate.
It is designed to perform effectively in tough
environments.
The 3550 features an oversized display (1.2”
high LEDs) which can be read more than 50
feet away.
The rugged stainless steel NEMA 4 enclosure
is washdown safe for use in industrial and
marine environments.
Standard features include a peak capture
function for stress analysis, RS-232
input/output, two programmable set-points, a
built-in surge protection which ensures
dependable operation and the capability to
drive up to eight 350 ohm load cells.
Optional features include the following: 6V
Rechargeable battery with a 130 hour charge,
two ...
(9) The Strainsert SJB Series Summing
Junction Boxes are for parallel averaging
of 2 to 4 similar transducers. The
standard SJB is available in a NEMA-
12 steel enclosure (NEMA-4X packages
are optionally available). The
NEMA-12 comes in both a connector
style and a cord grip style (NEMA-4X
available with cord grips only). Cord
grips accept cables with diameters
between 0.250” to 0.375” inches. The
removal of a gasket-tight lid enables
the user to make cable wire
connections to screw type terminal
blocks mounted on an internal
circuit board. Overall enclosure
dimension are 7.5” (L) x 4.25” (W)
x 3.5” (H).
Contact Strainsert
For information on load pins, force sensing bolts, load cells, tension
links, signal conditioners or our high quality custom products, Contact Us for further assistance.
