Strainsert Co. - Item # SXA, Standard Internally Gaged Hex Head Cap Screws, SXA Series

LOAD PINS

 
LOAD CELLS

 
INSTRUMENTS

 
BOLTS & STUDS

 
TENSION LINKS
 Search Catalog
      GO   
 All Categories    Standard Internally Gaged Hex Head Cap Screws, SXA Series
STRAINSERT….
     FOR SUPERIOR INTERNALLY GAGED FORCE TRANSDUCERS
Phone: 610-825-3310
Email: info@strainsert.com
All Categories > Force Sensing Bolts & Studs > Standard Internally Gaged Hex Head Cap Screws, SXA Series > Item # SXA  
    Download PDF Download PDF     Print Printable Page     Email Email This Page     Save To Favorites Save To Favorites
Request Information

Item # SXA Standard Internally Gaged Hex Head Cap Screws, SXA Series


    Download PDF Download PDF  
    Email Email This Page  
    Save To Favorites Save To Favorites
  

Bolt---Stud-Photo_page38

larger image

To measure accurate preload, service load and overload of bolted assemblies

For maximum uniformity, efficiency and reliability in bolted assemblies

For effective research, testing and manufacturing of bolted assemblies

Allowable Loads
Allowable loads for Strainsert Hex Head Cap Screws, as tabulated below, are based on approximately 70% Yield Strength of the threads, in pounds.
Load Capacity Lbs.
Screw Dia. Load
1/4-20NC 900
5/16-18NC 1500
3/8-16NC 2200
1/2-13NC 4000
5/8-11NC 6500
3/4-10NC 10000

Each cap screw is calibrated to above indicated load as part of quality control procedure. See calibration section for additional calibration certification.

For full configuration click Request Information button



Specifications · Performance Specs · General Information

Specifications

Material

Aluminum Alloy, 2024-T4

Hardness

Rockwell B54 Minimum

Ultimate Tensile Strength

55,000 psi Minimum; 60,000 psi average

Threads

Class 2A, rolled

Thread Length

2-diameters + 1/4 inch full threads + 3/16 inch maximum imperfect threads.

Calibration

Load Only Calibration (Standard)
Load & Unload Calibration

Performance Specs

Gages Type

Metal Foil

Gage Factor (Nominal)

2.00

Non-Linearity

±1% of Allowable Load

Non-Repetition

±0.1% FS

Excitation

350-ohm (Standard) FB: 12V (Maximum)
120-ohm FB: 3V (Maximum)

Output Signal (Nominal)

 Question? 		FB: 3.0 mv/V, approx.

Configuration

Full Bridge Strain Gage Circuit (Standard)

Bridge Resistance (Nominal)

 Question? 		350 Ω (Standard)
120 Ω

Service Temperature

150°F (Standard)
250°F (Max.)

General Information
Strainsert fasteners utilize an exclusive internal gaging method (U.S. Patent #2,873,341) to indicate bolt tension due to preload and subsequent service loads with strain gage accuracy. They are the first fasteners to provide a means for accurate, independent inspection of an assembled bolt for preload, thereby enhancing the structural integrity and reliability of both the bolt and the assembly.


Feature
  • Measurement of preload induced in fasteners
  • Accurate tightening of fasteners within 1% of induced load
  • Uniform tightening of fasteners in a bolt pattern


    		•

     MORE IMAGES 

    · Load Capacity

    · Force Sensing Bolt & Studs

     DOWNLOADS 

    width= Strainsert Force Calibration Service
    (PDF, 407KB)

    width= Overview and Application of Internally Gaged Force Sensing Fasteners
    (PDF, 454KB)

    width= Lead Wire and Ordering Information
    (PDF, 65KB)

    Request Information


    Contact Strainsert
    For information on load pins, force sensing bolts, load cells, tension links, signal conditioners or our high quality custom products, Contact Us for further assistance.